SerialPlate / Error codes / LG dryer
LG dryer error codes
29 codes. 14 are ones you can usually clear yourself, and 13 are ones LG says need a technician.
Tell us the code and we'll check it against your exact model, its age and any recalls.
| Code | What it means |
|---|---|
| tE1 | The dryer has found a problem with one of its temperature sensors. Needs a technician · also shown as tE3, tE4, tE5, tE6 |
| tE2 | A temperature sensor reading is off, usually because the dryer is cold. Steam cycles can set it off. You can usually clear it |
| drn | The dryer stopped because the water it collects isn't draining away. You can usually clear it · also shown as OE |
| LE1 | The drum isn't turning. You can usually clear it |
| LE2 | There is a problem with the compressor, the part that makes the heat on a heat-pump dryer. Needs a technician · also shown as AE, CE1 |
| LE3 | There is a problem with the motor that moves air through the dryer. Needs a technician |
| IF | There is a problem with the lint filter. You can usually clear it |
| E1 | On steam models, there is a problem with the part that makes steam. Needs a technician · also shown as E4 |
| d80 | Air isn't moving freely from the dryer to the outside. The number is roughly how blocked the vent is. You can usually clear it · also shown as d75 |
| d90 | The vent to the outside is almost completely blocked. You can usually clear it · also shown as d95 |
| nP | No current is reaching the heater. It is usually a problem with the house wiring, not the dryer. You can usually clear it |
| PS | The voltage at the power cord is wrong, possibly because two wires were swapped when the cord was fitted. Needs a technician |
| dE | The door isn't completely closed. You can usually clear it · also shown as dE4 |
| E13 | On hybrid condensing models, the collected water can't drain. You can usually clear it |
| FO | The lint filter isn't in properly, so the dryer has stopped. The display may also flash INSERT FILTER. You can usually clear it |
| HS | The moisture sensor isn't reading properly, so the dryer runs for two and a half hours and may seem not to dry. You can usually clear it |
| PF | The power was cut during a cycle. Not a fault |
| gAS | On a gas dryer, no gas is reaching it. Needs a technician |
| CL | Child Lock is on, so the dryer won't start. Not a fault |
| Add Water | A steam cycle needs water and the steam feeder is empty. You can usually clear it · also shown as Add, Add Error |
| E05 | On steam models connected to a tap, water for the steam cycle isn't arriving. You can usually clear it · also shown as E5 |
| E03 | A float switch has found the base of the dryer full of water. You can usually clear it |
| nE | The control panel can't communicate with the Wi-Fi module. Needs a technician |
| nF | There is a problem with the Wi-Fi module. Needs a technician |
| nC | The display board can't communicate with the NFC module. Needs a technician |
| bE | A problem with the drum's drive belt has stopped the drum turning. Needs a technician |
| E00 | The display board can't read the software from the main board. Needs a technician |
| EHE | The heater is drawing too much current, which can trip the breaker. Needs a technician |
| F1 | The heat-exchange system has stopped producing heat. Needs a technician |
Worth knowing
LG wrote this list for all its dryers, so some codes apply only to certain kinds: steam models, heat-pump models, or dryers with a water container.
Meanings read from LG support: dryer error code list and written in our own words. Last checked 11 November 2026. Codes differ between models; your manual lists the ones for yours. Shown as: tE1 or tE3 or tE4 or tE5 or tE6; tE2; drn or OE and so on.